Article: Characterization of Thermoplastic Polyurethane (TPU) and Ag-Carbon Black TPU Nanocomposite for Potential Application in Additive Manufacturing

Electromechanical, adhesion, and viscoelastic properties of polymers and polymer nanocomposites (PNCs) are of interest for additive manufacturing (AM) and flexible electronics. Development/optimization of inks for AM is complex, expensive, and substrate/interface dependent. This study investigates properties of free standing films of a thermoplastic polyurethane (TPU) polymer and an Ag⁻carbon black (Ag-CB) TPU PNC in a lightly loaded low strain compression contact as a rough measure of their suitability for AM. The TPU exhibited high hysteresis and a large viscoelastic response, and sufficient dwell time was needed for polymer chain relaxation and measurable adhesion. A new discovery is that large enough contact area is needed to allow longer time constant polymer ordering in the contact that led to higher adhesion and better performance/reliability. This has previously unknown implications for interface size relative to polymer chain length in AM design. The standard linear model was found to be a good fit for the viscoelastic behavior of the TPU. The PNC exhibited no adhesion (new result), low electrical resistance, and relatively small viscoelastic response. This implies potential for AM electrical trace as well as switch applications.

Citing Articles

A Coherent Assessment of the Compressive Strain Rate Response of PC, PETG, PMMA, and TPU Thermoplastics in MEX Additive Manufacturing.

Petousis M, Ntintakis I, David C, Sagris D, Nasikas N, Korlos A Polymers (Basel). 2023; 15(19).

PMID: 37835975 PMC: 10574899. DOI: 10.3390/polym15193926.

Polymeric Biocomposite Based on Thermoplastic Polyurethane (TPU) and Protein and Elastomeric Waste Mixture.

Nituica M, Oprea O, Stelescu M, Sonmez M, Georgescu M, Alexandrescu L Materials (Basel). 2023; 16(15).

PMID: 37569981 PMC: 10419917. DOI: 10.3390/ma16155279.

Viscoelastic Behaviour of Flexible Thermoplastic Polyurethane Additively Manufactured Parts: Influence of Inner-Structure Design Factors.

Pelayo F, Blanco D, Fernandez P, Gonzalez J, Beltran N Polymers (Basel). 2021; 13(14).

PMID: 34301120 PMC: 8309542. DOI: 10.3390/polym13142365.

Shape Memory Polyurethane-Based Smart Polymer Substrates for Physiologically Responsive, Dynamic Pressure (Re)Distribution.

Kumar B, Noor N, Thakur S, Pan N, Narayana H, Yan S ACS Omega. 2019; 4(13):15348-15358.

PMID: 31572833 PMC: 6761750. DOI: 10.1021/acsomega.9b01167.

Modeling the Temperature Dependence of Dynamic Mechanical Properties and Visco-Elastic Behavior of Thermoplastic Polyurethane Using Artificial Neural Network.

Kopal I, Harnicarova M, Valicek J, Kusnerova M Polymers (Basel). 2019; 9(10).

PMID: 30965826 PMC: 6418911. DOI: 10.3390/polym9100519.

References

1.

Kanyanta V, Ivankovic A . Mechanical characterisation of polyurethane elastomer for biomedical applications. J Mech Behav Biomed Mater. 2009; 3(1):51-62. DOI: 10.1016/j.jmbbm.2009.03.005. View

2.

Yeo J, Hong S, Lee D, Hotz N, Lee M, Grigoropoulos C . Next generation non-vacuum, maskless, low temperature nanoparticle ink laser digital direct metal patterning for a large area flexible electronics. PLoS One. 2012; 7(8):e42315. PMC: 3416833. DOI: 10.1371/journal.pone.0042315. View

3.

Yao S, Zhu Y . Wearable multifunctional sensors using printed stretchable conductors made of silver nanowires. Nanoscale. 2014; 6(4):2345-52. DOI: 10.1039/c3nr05496a. View

4.

Yung L, Fei C, Mandeep J, Binti Abdullah H, Wee L . Synthesis of a nano-silver metal ink for use in thick conductive film fabrication applied on a semiconductor package. PLoS One. 2014; 9(5):e97484. PMC: 4022582. DOI: 10.1371/journal.pone.0097484. View

5.

Davis C, Lemoine F, Darnige T, Martina D, Creton C, Lindner A . Debonding mechanisms of soft materials at short contact times. Langmuir. 2014; 30(35):10626-36. DOI: 10.1021/la5023592. View